SIGMA Ceramic Clean 10L white ceramic paint for painting walls, ceilings, interior

€ 111.00

GBP: 93.47£

50 in stock

Category: Sigma coating

Description
Additional information

SIGMA Ceramic Clean 10L White Ceramic paint for interior walls and ceilings

Ceramic Clean color Water-based based on high-quality acrylic dispersions for painting interior walls and ceilings made of cement, cement-lime plaster, concrete surfaces, gypsum plaster, gypsum plasterboard and surfaces painted with emulsion paints.

Lacquered surfaces are characterized by the highest dirt and disinfection resistance of various cleaning agents and disinfectants.

Particularly recommended for surfaces that are exposed to intensive use in public facilities such as schools, kindergartens, hotels as well as in the catering and food industry.

Main advantages:

highest scrub resistance, class 1 according to EN 13300 (loss <1 µm after 200 scrub cycles)
Ceramic hybrid technology
Stain-Repellent & Water-Repellent - Repels liquid dirt
Class A + emission of the substance (lowest)
high resistance to the most common disinfectants and cleaning agents
very good flow
excellent application
odorless
meets all radiation hygiene requirements

Technical specifications:

Colors Colors available in the Color Pro computer color system. Palettes: Chromatic, NCS, RAL and others.

Density 20 ± 0.5 ° C, [g / cm³] 1.23 ≤ 1.31

Haake viscosity 23 ± 1 °C, [dPa * s] 41.0 ÷ 80.0

Coating drying time at 23 ± 2 °C, [h] 4 h

Application of the second layer [h] after 6 hours

Brush, roller or spray application method

Solids content, min. [wt%]

7.5 ÷ 8.5

Degree of whiteness [%] (applies to white)

Recommended wet film thickness [μm] 140

scrub resistance

class 1

shell appearance

cloudy

Largest grain size (granulation) [μm] Fine up to 100

Contrast Ratio (Opacity)

Class 2 at 7 m2 / l

Recommended number of coats 1-2

Cover 7 to 9 m2 / l with one layer depending on the absorbency and roughness of the substrate

BREEAM HEA9

VOC emissions measured according to ISO 11890-2:2006 Regulatory Standards (g/l) Meets the requirements of BREEAM HEA9

0.0g/L 30g/L Yes

LEED IEQ4.2 – 2009

VOC emissions measured in an anhydrous package Regulatory standards (g/l) Meet LEED IEQ4.2 requirements

0.0g/L 50g/L Yes

Substrate preparation:

Thoroughly remove adhesive residue and wash the surface with water. Remove any badly bonded and peeling old paintwork to reveal the correct surface.

The surface to be painted should be clean, dry, dust-free, crack-free and evenly absorbed.

Plaster and substrates that absorb a lot of water (paints and gypsum plaster, plasterboard, never painted surfaces) should be primed with Sigmafix Universal.

Milled surfaces should be cleaned with an aqueous disinfectant solution using a brush. Surfaces coated with emulsion paints can be degreased by washing with water with the addition of cleaning agents (e.g. lacquer soap).

Surfaces painted with alkyd paints should be degreased and matted to increase adhesion.

The surface should be repaired with lime-free materials. Smooth surfaces without structure should be evenly aligned.

Painting:

Paint fresh cement-lime plaster 3-4 weeks after application. Mix the product thoroughly before use. If necessary, with water in an amount of max. 5% vol. Wash the tools with water after painting.

Before use, ventilate the room until the characteristic smell before painting disappears.

Additional Information:

For hard-covering paints, use the primer recommended in the paint system. Painting work should be carried out at a substrate and an ambient temperature of +5 to +30 ° C and relative humidity below 80%. It is not recommended to apply the product at low relative humidity.

The coating regains its full mechanical properties after 4 weeks. Most dirt can be removed with lukewarm water and a soft cloth 4 weeks after painting. To remove contaminants such as coffee, tea, and wine, use water with a small amount of detergent.

Won't pick up dirt and stains such as ketchup, mayonnaise, mustard, cola, oil, chocolate, chalk, lipstick, orange juice, carrot, blackcurrant and beetroot concentrate (remove up to 1 hour). Coffee, Tea, Wine (remove up to 15 minutes)

Lower temperatures and higher relative humidity increase the drying time of the coating. A water-based product, not frost resistant. Store above 0°C in a cool and dry room.

The optimum level of cleaning is achieved when Ceramic Clean is cleaned after full curing, which occurs after a period of approximately 3-4 weeks after the last coat has been applied. Most dirt can be removed with lukewarm water and a soft cloth. For some colors available in the computer color system, individual batches of the product may differ slightly in shade after dyeing.

In order to avoid differences, it is necessary to produce a surface that represents a separate architectural whole in one work cycle with products from the same production batch. If you have products from different production batches, it is recommended to mix them to unify the shade.

All corrections should be made using the “wet on wet” method. Before applying the product, check the color compliance in all packaging with the order.

The paint meets all the requirements of the technical conditions for the implementation and acceptance of construction work according to ITB edition no. 387/2011 part B: finishing work, edition 4: exterior and interior coatings, chap. 6. Paint finish requirements.

Colours :

White and 65 colors available in the computer color system Color Pro.

Caution: For an additional fee, we will color the selected color from the template!

* ONLY ORIGINAL FROM THE MANUFACTURER *

MasterBau has been active on the European market for 10 years as a distributor of various building materials from Caparol, Graco, Fakro, Tytan, Knauf, Mapei and many others.

We will ensure delivery across Europe.

Our motto is customer satisfaction through the highest quality of the delivered products.

Some of the products we have purchased can be returned in their original sealed packaging or in their original condition within 14 days without giving a reason.

Returns are made at the buyer's expense.

If you have any complaints, please contact the following address:

MasterBau

Mariana Rapackiego 21A

71-899 Szczecin

Poland

valuation

We welcome any positive review.

If you are unsatisfied or have any problems with shipping, please don't hesitate to contact us before evaluating.